What Is Topology Optimization? A Primer for Design Engineer

Have you come across images of exotic, organic looking part shapes in CAD graphics windows? Do they look like flights of fancy, rather than disciplined work? These shapes may be the result of a topology optimization study. This type of application is now readily available - so you can try your hand!

Rendering of part created with topology optimization.

In a sense these shapes are indeed flights of fancy. However, they originate not from a human mind, but rather from the determined logic of a computer algorithm.


Topology optimization takes a 3D design space and literally whittles away material within it to achieve the most efficient design. The method doesn’t care about aesthetics, traditional approaches, or any other of the usual design constraints that you would normally use in design. At its simplest level, if you define the loading and the constraint system, it will figure out the material needed to develop that load path.

Behind the scenes

The technology behind this magic starts with a very regular finite element analysis (FEA) mesh occupying the design space you have defined. An initial FEA will show the stress distribution throughout this design space, but also show which regions are working efficiently.


Each element reports back its stress level and strain energy; essentially, how hard is it working. Those elements which are not picking up much stress and have little strain energy are doomed. The topology optimizer will remove them from the mesh.


However, as it removes these elements it will keep an eye on whether the overall evolving structure is affected by their departure. In some cases, the elements may be reprieved.


The topology optimizer has a target number of elements to get rid of. This is based on the target volume fraction you set. If you aim for a fraction of 30%, then you are sending 70% of the elements in a regular mesh to the chopping block. In practice, the removal of elements won’t be attempted in one hit. The target volume fraction will be approached in steps. At each step the distribution of elements will iterate so that the stress state stabilizes.

A topology optimization study in Creo 5.0

The kill zone

In many optimizers the action is slightly subtler than this. Deleting elements from the mesh at each step is technically complicated and computationally expensive.


Instead of using this “hard kill” method, the system takes a “soft kill” approach. The element stiffness is dropped down to a near chewing gum level. The density is dropped in a similar manner. The element is still there, but it has been marginalized.


Many optimizers further relax this strict segregation between the parent materials, let’s say steel (with a relative density 1.0) and chewing gum (with a relative density close to 0.0). An element can adopt any stiffness and density across a range between these two limits. However, each element is “encouraged” to migrate to a value of 1.0, or 0.0 –with a big penalty if it is caught sitting between.

Shades of grey

In many cases, optimizers won’t be able to achieve the limiting values of 1.0 or 0.0 for all elements. Some will end up with some value in between. So, what does it mean to have the relative material property in an element set to 0.8?


It doesn’t represent anything physically, but to the optimizer it represents the most efficient distribution of material. Using a grayscale to represent material distribution will show regions of parent material in white (1.0) and chewing gum in black (0.0), and shades in between


If the optimizer is struggling, then large regions of the resulting configuration will be varying shades of grey. If the optimizer can find a well-defined load path, then the distribution will be clearer, migrating towards black or white.


So where does the exotic shapes come from that I described in the introduction? They do not represent the element faces, instead they are surfaces fitted through the grey-scale contours. The smoothness of the surfaces is very largely controlled by how fine the underlying FEA mesh is and how well distributed the parent material is.

You are in control

Topology optimization is sometimes described as a wild ride! It is great at coming up with radical solutions – the flights of fancy as I call them. However, there are many controls available to the engineer to help steer towards more usable configurations.


These include manufacturing constraints, such as limiting the size of members within the design space, dictating that components must be symmetric about planes, or extrudable, or can be drawn from a mold, and so on. By choosing the volume fraction you can control how aggressive the optimizer will be.


I have many hints and tips on how to approach topology optimization and get the best out of it. I will be sharing those in upcoming articles.

Follow us on

CADOpt Technologies

CADOpt Technologies, founded in 2014, is a company providing Engineering Services and Solutions, mainly in the areas of CAD (Computer Aided Design) / CAM (Computer Aided Manufacturing) / CAE (Computer Aided Engineering) / IoT & AR, to firms in the field of Automotive, Aerospace, Heavy Engineering, Medical Devices, Home Appliances, etc..

Testimonial

Reach Us

  CADOpt Technologies
       3M-407, 2nd Floor, 3rd Main Road
       East of NGEF Layout,
       (Next to HDFC Bank)
       Kasturinagar, Bengaluru- 560 043
  +91 80 4852 2824
   +91 960 646 3560
    +91 960 646 3560
   GST : 29AAFCC8405K1ZD
   CIN :U 74900KA 2014 PTC 077156
   Email: info@cadopt.com
                    marketing@cadopt.com

All rights Reserved to CADOpt Technologies